Browsed by
Tag: compressor working

Compressors – Working and Characteristics

Compressors – Working and Characteristics

Comments 0 Comment

Compressors are used to increase the pressure of a gas. Like pumps, compressors can be classified as either kinetic machines, which includes centrifugal and axial compressors, or positive-displacement machines, which include reciprocating and rotary compressors. The compressing medium or ‘gas’ depends on the application, such as, if air is used it is termed as an air compressor. Similarly if refrigerant is used, it is known as a refrigerant compressor. The type of compressor, its discharge pressure and discharge rate is dictated by its use.

compressors_onboard
Air Compressors

Types of compressors

Here we discuss about two types of compressors that are commonly used in the industry.

Reciprocating Compressor

In a reciprocating compressor, gas is compressed by mechanical variation of the volume of space inside the cylinder, by reciprocating motion of the piston.
For a cycle of operation, there are two strokes such as,
1.) Suction stroke, and
2.) Compression stroke
As the piston moves down, air is sucked from atmosphere to the cylinder through suction valve (a non-return valve). As piston moves up, air is compressed and at the end of compression stroke, air is delivered through delivery valve (which is also a non-return valve). Topmost portion the piston can travel inside the cylinder is is called Top Dead Center (TDC), and bottom most portion the piston can reach inside the cylinder is called as Bottom Dead Center (BDC).
RECIPROCATING AIR COMPRESSOR
RECIPROCATING AIR COMPRESSOR

Screw Compressor

Screw compressors (also called as helical lobe compressors) are positive displacement machines in which gas is being compressed is forced through the casing by two screws. Unlike the reciprocating compressors which are also positive displacement machines, screw compressors does not typically require internal suction or discharge valves. In addition the flow from screw compressor is generally more uniform and has fewer pulsations than the flow from a reciprocating compressor.

A twin screw compressor consist of two meshing helical rotors mounted on counter rotating parallel shafts that are enclosed within close-clearance casing. One screw is called driving screw which is coupled with a drive, say an electric motor, while the other screw is called as the driven screw, since it is driven by the driving screw. Gears used for driving the screws are called timing gears, since they are properly timed to maintain the close-clearance between the screws.

SCREWS OF A TWIN SCREW COMPRESSOR
SCREWS OF A TWIN SCREW COMPRESSOR

For screw compressors oil is injected into the screws while operation. There are mainly 3 functions for the oil, they are,

1) Sealing of the screws to prevent leakage of the gas

2) Lubrication of the parts, especially the screws, and

3) Cooling of the gas compressed, which results in increased efficiency of the system

Materials used for construction

Reciprocating Compressor

Crankcase and body – Cast Iron
Crankshaft – Spheroidal graphite cast iron or stainless steel
Connecting rod – Forged Steel
Piston – Aluminium Alloy or Cast / Ductile Iron

Piston Rings – Cast Iron

Screw Compressor

Casing – Cast or Ductile Iron

Screw  – Steel or Stainless Steel or Nickel Alloy

Where they are used?

Reciprocating Compressor

Reciprocating compressors are characterized with higher pressures and reduced mass flow rate. They are mainly used in high pressure applications since it can deliver air at about 30 – 40 bar.

1) For diesel engine starting, where electric motor starting becomes costly and impractical.
2) Refrigeration compressors are normally reciprocating type (Single Stage) with a discharge pressure around 10 bar.

3) Air conditioning systems also uses reciprocating compressors (Nowadays trend is changed to screw compressors).

Screw Compressors

Screw type compressors provide air at increased mass flow rate but with reduced discharge pressure around 8 bar. Hence applications are also in low pressure systems, such as,

1) Service air compressors used in industry (For cleaning air, etc.)
2) Air conditioning systems nowadays employ screw compressors. (which have low power consumption and increased mass flow rate as advantages)
3) For low pressure air required for running pneumatic tools, pneumatic-hydraulic equipment, etc.

Cycle of operation

Consider one cycle of operation in a reciprocating compressor.

ONE COMPLETE CYCLE OF OPERATION
ONE COMPLETE CYCLE OF OPERATION

The process that occurs in a cycle 1-2-3-4-1 are explained below

The process that occurs in a cycle 1-2-3-4-1 are explained below

  • (3) – (4) – As piston travels from BDC to TDC air trapped inside the cylinder is compressed.
  • (4) – (1) – As piston approaches TDC discharge valve opens and compressed air is delivered.
  • (1) – (2) – Undelivered air trapped in the clearance space is expanded as piston moves down.
  • (2) – (3) – When trapped air in the clearance space is expanded to atmospheric pressure, further downward movement of the piston creates a vacuum inside the cylinder and thereby atmospheric air enters through suction valve.

Again cycle repeats.

In fig. ‘Va’ indicates the volume corresponding to actual stroke of the piston from TDC to BDC (also called stroke volume). Similarly ‘Ve’ indicates the volume corresponding to the effective stroke of piston, when atmospheric air enters the cylinder.
The ratio of effective stroke volume to the swept volume is known as the volumetric efficiency of the compressor,

Voleff = [ ( Ve / Va ) * 100 ] %

Then why clearance space?

It was already seen from the above equation that volumetric efficiency is 100% when
Effective stroke = Actual stroke
In other words, no clearance volume exists. This is practically impossible, because some clearance space is required otherwise piston hits on the cylinder head as it travels. Also expansion of piston occurs as it travels and very little clearance may cause the same problem. Also increased clearance space reduces compressor efficiency and increase its running hours. So clearance volume must be kept around a reasonable value as instructed by the manufacturer.

How to measure clearance volume

The clearance between piston and cylinder head while piston at TDC is called bumping clearance. This can be measured in different ways. One common method is, remove the valves from the top of the piston. Put a lead ball of sufficient diameter into the cylinder. Slowly turn the flywheel one revolution by hand. Take out the lead piece and measure its thickness, which gives the bumping clearance.

Why cooling is required?

Reciprocating compressors are generally cooled with air or water. The cylinders in air cooled compressors often include large external fins that increase the surface area available for heat transfer.
In water cooled compressors, freshwater is circulated through jackets that are built into the walls of the cylinders and cylinder heads.
The compression cycle is illustrated graphically down below.
single_stage_compression
Single Stage Compression

Above cycle compresses gas from atmospheric pressure to 8 bar in a single stage. The area enclosed by the points 12341 represents the work of compression in a single stage compressor. Also see the cycle or Pressure-Volume diagram (P-V) below which compresses gas from atmospheric pressure to 8 bar in two stages.

Two stage compression is shown below.

two_stage_air_compressor
Two Stage Compression

Here first stage compresses gas from atmospheric pressure to 3 bar and then gas is cooled isobarically (at constant pressure, refer diagram above). Now gas is again compressed to 8 bar. Now we can see that the work of compression corresponding to the shaded area in the diagram is saved by incorporating an inter cooling between two stages. Hence when comparing with a single stage compressor work can be reduced by inter cooling in a multistage compressor.

Work can be reduced further by increasing number of stages and inter cooling, but as the number of stages increases design becomes complex, constructional cost increases, maintenance cost also increase, which may nullify the effect of work saved during operation. This is the limiting factor for more number of stages.

Refer figure below.

isothermal_adiabatic_polytropic_compression

The indicator card (PV diagram) above shows 3 types (or processes) of compression possible.

Isothermal Compression

During the process of compression, whatever heat produced is taken away by a cooling medium. In other words, it is the compression , keeping temperature of the gas constant. For a process to be isothermal, the process must be very slow, which is impractical. From the indicator card, it is clear that, work of compression is minimum in isothermal compression.

Also,

expression_for_isothermal_compression

Adiabatic Compression

Whatever heat produced during compression is kept inside the gas only, or heat transfer is zero in an adiabatic compression. For a perfect adiabatic process, process must be very fast. All the thermodynamic process resembles adiabatic process. It can be seen from the indicator card that, work of compression is maximum in adiabatic compression.

Also,

expression_for_adiabatic_compression

Specific heat is defined as the heat energy required to raise the temperature of unit mass of substance by unit degree.

Polytropic Compression

Polytropic compression is neither isothermal nor adiabatic. It comes in between.

Also,

expression_for_polytropic_compression

Work of compression can be minimized by isothermal compression. But compression is practically a fast process. So it better resembles an adiabatic process. Jacket cooling of compressor makes the compression polytropic.

Now the only way to make the compression more isothermal is, by dividing the process to a number of stages. Between every stage inter cooling of gas is done. Hence the work can be saved substantially.

Refer the diagrams below.

work_saved_in_compression_stages

 

 

    HP P