Marine Engineering Study Materials

Maintaining Efficiency of an Air Compressor on Ships

What is volumetric efficiency of an air compressor ?

What are the factors affecting volumetric efficiency of an air compressor ?

  1. The bumping clearance (the larger the bumping clearance the less air is discharged per stroke).
  2. Sluggish opening and closing of suction and delivery valves.
  3. Leakage past compressor piston rings.
  4. L.P inlet air temperature too high.
  5. L.P inlet filter dirty and choked.
  6. Inlet cooling water temperature too high.
  7. Insufficient cooling water owing to fouling of coolers.

What is the difference between inter cooler and after cooler ?

Intercooler

  1. Fitted intermediate stages.
  2. Saving in power. 
  3. Increase volumetric efficiency.
  4. Reduce temperature for next stage and it can avoid a danger of explosion in compressor cylinder.
  5. Can provide good lubrication of the compressor piston.
  6. No carbonized material forming of discharge valve.
  7. Moisture separation is easier through intercooler drain.

After cooler

  1. Fitted at the final stage discharge side.
  2. Reduce final discharge air temperature to room temperature.
  3. Increase volumetric efficiency.
  4. Air bottle size is smaller.
  5. Moisture separation is easier through after cooler drain.

Why need bumping clearance in an air compressor ?

How to adjust the bumping clearance ?

It can be adjusted by two ways.

  1. By altering the head gaskets (cover joint ) thickness.
  2. By adding and subtracting shims between the connecting rod foot and bottom and bearing.

Main air compressor bumping clearance taking procedure ?

  1. Stop the compressor and (lock off) take out fuse.
  2. Drain the cooling water.
  3. Remove the cylinder cover.
  4. Clean the cylinder head face and piston crown.
  5. Place the lead wire ball on the top face of the piston. That is larger size than expected by clearance.
  6. Cylinder cover is placed on the cylinder with correct joint thickness and tightens the head bolts.
  7. Turn the compressor slowly by hand over top centre so that lead wire ball is pressed.
  8. Then remove cylinder cover again.
  9. Remove the compressed lead wire ball.
  10. Take the measurement of lead wire thickness by using micrometer.

At what condition fusible plug is fitted main air bottle ?

What is the purpose of bursting disc? Where is it fitted ?

Why bursting disc need to be annealed ?

What is first start arrangement on ships ?

  1. Firstly start the emergency air compressor to fill up the air to the emergency air bottle up to desired pressure obtained.
  2. Drain out oil and water.
  3. Open emergency air bottle outlet valve and pressed up desired pressure.
  4. Then start the generator with correct procedure.
  5. Close the breaker and switch on the lighting.
  6. Start the required machinery ( especially G/E FO booster pump, SW cooling pump, E/ R blower).
  7. Start the main air compressor and press up to main air bottle.
  8. After that, M/E warming by using generator jacket water and start the L.O pump.

Why provide air compressor on board ships ?

 Why need minimum lubrication for air compressors ?

Leaky Valves in Air Compressors

Valves can leak and finally fail. Valves may fail owing to wear and fatigue, insufficient of over-lubrication, presence of foreign particles, oil decomposition and excess valve lift.

What are the effects of air compressor valve leaking on ships ?

First stage suction valve leaking

  1. Reduce air delivery
  2. Reduce second stage suction pressure
  3. Increase running time
  4. Unload the compressor (Motor take less load)

First stage delivery valve leaking

  1. Reduce delivery
  2. Increase discharge temperature
  3. Less air drawn in due to high pressure air leaking back into the cylinder

Second stage suction valve leaking

  1. High pressure in suction line of 2nd stage
  2. High temperature in suction line of 2nd stage
  3. Reduce delivery
  4. Increase running time

Second stage delivery valve leaking

  1. Increase suction pressure in 2nd stage
  2. Reduce delivery in 2nd stage
  3. Increase delivery pressure from 1st stage

What are the causes of poor performance of air compressors ?

  1. Choked air suction strainer
  2. Leaky or sticky valves
  3. Too much L.P bumping clearance
  4. Leaky piston rings
  5. Leaky cylinder head cover and gaskets
  6. Leaky drains
  7. Leaky relief valves
  8. Leaky coolers
  9. Worn crankpin bearings
  10. Faulty capacity controller

How to maintain air compressor efficiency ?

  1. Cleaning of suction air filter.
  2. Adjusting bumping clearance.
  3. Regular overhaul the suction and delivery valve and checking bearings.
  4. Check the piston rings and liner.
  5. Clear the cooler drain free from deposits.
  6. Clean the cooler regularly.

How air bottle pressure test is carried out in ships ?

  1. Gag the relief valve
  2. Close all openings
  3. Fit test pressure gauge
  4. Remove filling valve and fill with fresh water completely
  5. Air purge and connect hydraulic pump at filling line.
  6. Apply pressure 1.5 times of working pressure and maintain at least 30 min
  7. Check leaking points.

 What is the purpose of drain valve in compressor and air bottle ?

 

Reference:

Oral Guide by – MIN ZAR TAR

Exit mobile version